Remote Controlis being used to control a TV, VCR or CableNOTE :Pressing one of these buttons selectsfrequency up or down in single-step increments.of the input sources connected to the AVR-35.
box.,press these button to change the channelthe source only. In order to control the actualWhen the FM band is in use, pressing this buttonAfter pressing this button, use the / buttons
being viewed.source machine using the remote you mustwhen a station's signal is weak will change toto make your selection betweenOPTICAL
press the Press Control Selectorbuttonformonaural reception, as indicated by theMONOor COAXIALdigital. Press the Set button
Surround Mode Selector : Press thisthe desired product.indicator .to enter your choice.
button to begin the process of changing the
surround mode. After the button has been+10 Button :This button does not have aDirect/Enter : Press this button to select aSpeaker Configuration : Press this button
pressed, use the / buttonto select thefunction for the AVR35, but when the remote isradio station by entering its frequency using theto begin the process of configuring the AVR-35's
desired surround mode.used to control certain CD players, TV sets andNumeric Key14 .Bass Management System for use with the type
VCRs it may be used to select tracks or channelof speaker used in your system.
/ Buttons : These are multi-purposenumbers.Enter : This button does not function withOnce the button has been pressed, use the /
buttons. They will be used most frequently tothe AVR35, but it is available for use with otherbuttonsto select the channel you wish to
select a surround mode. To change the surrou-Numeric Keys :These buttons serve as adevices.set up. Press the Set button10 , and then select
nd mode, first press the SURR button. Nextten-button numeric key-pad to enter tuner presetanother channel to configure. When all
press these buttons to scroll up or down throughpositions. They are also to be used to selectPresetUp/Down:Whenthetunerisinuse,adjustments have been completed, press the Set
the list of surround modes that appear in thechannel numbers when TV has been selectedthese buttons scroll through the stations thatbutton twice to exit the settings and return to
Information Display. These buttons are alsoon the remote, or to select track numbers on ahave been programmed into the AVR-35'snormal operation.
used to increase or decrease output levels usedCD, DVD or LD player, depending on how thememory, When many source devices, such as
to lower the AVT35's output levels whenremote has been programmed.CD players, VCRs and cassette decks, areMute : Press this button to momentarily
configuring the unit with either the intermal testselected using theDevice Control Selectorssilence the AVR35 or TV set being controlled,
tone or an external source. They are also usedNOTE :The 0 button has a dual function. It also. these buttons will normally function asdepending on which device has been selected.
to enter delay time settings after the Delay butt-serves as the CLEARbutton for use inchapter step or track advance.
on24 has been pressed.programming the tuner or clearing the systemWhen the AVR35 remote is being programmed
memory.Tuning Up/Down : When the tuner is in use,to operate another device, this button is
/ Channel Button : This button is usedthese buttons will tune up or down through thepressed with the Device Control Selector
to start the process of setting the AVR-35'sInfo Button :This button dose not functionselected frequency band. If theTuner Modebuttonto begin the programming process.
output levels to an external source. Once thiswith the AVR-35, but it is available for use withbuttonhas been pressed so that the
button is pressed, use the / buttons8 toother devices.AUTO indicatoris illuminated, pressing theseVolume : Press these buttons to raise or
select the channel being adjusted, then pressbuttons will cause the tuner to seek the nextlower the system volume.
the Set button , followed by the / buttonsClear Button :This button dose notstation with acceptable signal strength for quality
again to change the level setting.function with the AVR-65, but it is available forreception. When the AUTO indicatoris NOTTest : Press this button to begin the seque-
use with other devices.illuminated, pressing these buttons will tunence used to calibrate the AVR-35's output levels.
Set Button : This button is used to enterstations in single-step increments.
settings into the AVR-35's memory. It is alsoMemory Button :Press this button to enterTV/VCR : This button does not function
used in the setup procedures for delay time,a radio station into the AVR-35's preset memory.Transport Control : These controls do notwith the AVR35, but it is available for use with
speaker configuration and channel output levelAfter pressing the button the MEMORYindicatorcontrol any function of the AVR-35, but they areother devices.
Program/Command Indicator :This LED isbeen pressed to confirm your selection.
adjustment.will flash, and you then have five seconds toused extensively when operating a wide variety
used as an indicator to assist in programming
enter a present memory location using theof CD players, cassette decks and VCRs.
the AVR-35. Note that the button will briefly turnPower Button : Press this button to turn the
Night Mode : Press this button to activateNumeric Keys .
red after it has been pressed to confirm yourcurrently selected device on or off.
the "Night" mode, preventing loud playbackDelay/Prev Ch. : Press this button to begin
selection.
when the digital modes are in use withoutNOTE :Although the word "Sleep" appearsthe process for setting the delay times used by
Sleep Button :Press this button to place
altering the dynamic range of the output signal.above this button, it refers to control of devicesthe AVR-35 when processing surround sound.
AVR Selector :Press this button to use thethe unit in the Sleep Mode. After the time shown
other than the AVR-35. Use the SleepbuttonAfter pressing this button the delay times are
remote control for operation of the AVR-65. Notein the display, the AVR-35 will automatically go
When the AVR-35 remote is being programmedto control the AVR-35's Sleep function.entered by pressing the Set button, and
that the button will briefly turn red after it hasinto the standby mode. Each press of the button
to operate other devices, this button is pressedthen using / buttonsto change the
been pressed to confirm your selection.changes the time until turn-off in the following
to begin a readout of a programmed code.Tuner Mode :Press this button when thesetting. Press the Set button again to complete
order:
tuner is in use to select between automaticthe process.
Device Control Selectors :Press one of908070605040
min min min min min minSource Selectors : Press these buttons to
tuning and manual tuning. When the button is
these button to use the remote to control the30201051OFF
min min min min min minselect an input source for the AVR-35. The AM/pressed so that the AUTOindicatorgoes out,/ Digital Button : This button is used to
functions of another audio/video device. Note
FM button is also used to switch betweenpressing the Tuningbuttonswill move theselect the type of digital input used with any one
that the button will briefly turn red after it hasChannelButtons :When the remote
frequency bands when the tuner in use.
7 |
ACEC
